Drie chromen 9 Super 7® carburateurs naar 4-blaas inlaatspruitstuk-adapterset

This tri power kit allows you to put three Elevemotors 9 Super 7® carbs on your standard 4 bbl intake manifold. It includes three carbs, the adapter, air cleaners, progressive linkage kit, fuel block, fittings and red fuel line. Assembly required.

Note: Kit will NOT work with HEI distributors due to clearance issues. This system must be used in conjunction with a small diameter-based distributor.

Additional Note – There are NO vacuum ports on these carbs so you may need to tap into the manifold for a vacuum source.

Overall Height – 11 7/16″ total from the bottom of the adapter to the top of the air cleaners.
Adapter manifold top 3×2 dimension is 4” wide by 13-11/16” long
Adapter manifold is 2-3/16” tall bottom to top without the gaskets
4 barrel bolt pattern is 5-1/8” side to side and 5-5/8” front to rear
2 barrel bolt pattern is 3-1/4” side to side by 1-7/8” front to rear
Progressive linkage included
De pakking van inlaatspruitstuk naar adapter wordt NIET meegeleverd. 4 vaten carburateur basis pakking
The 9 Super 7® Carb® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that’s required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs. See our for more information on using the 9 Super 7® in a 2×2 or 3×2 carb set-up.

Three Deuce carburetor setups come with two „secondary“ carbs for front and rear intake position and one „primary“ carb for central/middle position
Volledig nieuw gereedschap voor scherpe, onberispelijke gietstukken
Nieuwe aluminium basisassemblage zorgt voor koelere brandstoftemperaturen en een betere brandstofefficiëntie in vergelijking met het oorspronkelijke gietijzeren ontwerp
Roestvrijstalen schroeven en hardware
Oorspronkelijke problematische naald en zitting vervangen door een Grose-stijl brandstofinlaatklep om beter om te gaan met hogere brandstofdrukken en verbeterde werking bij hoge snelheden
Blijft niet plakken of druppelen zoals de oude naald en zitting met Viton-tip
Verlengde messing gasklepschacht om het koppelen van meerdere carburateurs te vereenvoudigen
Primary Carb – (1) Middle Position
Choke-assemblage, gaspedaalpomp en jets zijn allemaal trouw behouden en accepteren standaard Stromberg-onderdelen.
Secondary Carb – (2) Front and Rear Position
Special base plate with no idle circuits or choke linkage
Special butterflies and shafts installed
Works best with progressive linkage
Idle only off the center or main carburetor
No more plug foul
Note: The secondary carbs have NO choke, and they have NO idle system.

9 Super 7® Primaire Koolhydraten -

Features .045″ main metering jets and a number 65 power valve, which is the same as a stock 97 carb.
Vervangende pakking voor toegang tot de jet gebruikt # 91011542, vervangende pakking voor naald en zitting gebruikt # 91011543.
Inclusief basispakking.
The 9 Super 7® ® will operate suitably with fuel pressures ranging from 1-1/2 psi to 4 psi, with a desired setting of 2-1/2 psi to 3 psi. Fuel pressure from 4 psi to 7 psi will cause the carburetor to run excessively rich and may cause flooding. Flooding or leaks caused by excessive fuel pressure do not indicate a faulty carburetor. A fuel regulator such as # 560-58500 must be utilized in order to keep proper fuel pressure at the 1-1/2 to 4 psi range.
Onze onafhankelijke tests leverden deze debietcijfers op:
3″ vacuüm - 60 CFM
10″ vacuüm - 110 CFM
15″ vacuüm - 136 1/2 CFM
28″ vacuüm - 184 CFM